Sanwa STD5000M Calibrator
Sanwa STD5000M Calibrator
STD5000M is a calibrator with soft touch buttons that can output desired DC voltage/current, AC voltage/current, resistance, frequency, etc. with a high degree of accuracy and stability. The STD5000M is equipped with a memory function that allows a wide range of uses for the device.
Sanwa SE300 Non-contact Digital Tachometer
Sanwa SE300 Non-contact Digital Tachometer
- Designed for ease of holding to enable stable measurement
- Max/Min value hold
- Auto power off (2min.) (cancelable)
- Fixed installation possible using a commercially available camera tripod
- Contact measurement (optional ENC-3)
Sanwa LCR700 LCR Meter
Sanwa LCR700 LCR Meter
- Measuring Frequency DC~100kHz
- Ls/Lp/Cs/Cp measurement with sub parameters (D/Q/θ/ESR)
- Automatically selectable L/C/R measurement
- Device Sorting mode
- Optical link USB interface(optional) : LCR-USB
- Data hold, Back light
Sanwa KS1 3Phase Detector
Sanwa KS1 3Phase Detector
This instrument is a 3 phase detector that allows you to determine the open phase and rotating direction.
- Phase sequence and open phase check
- Large size alligator clips
Sanwa DM509S Insulation Tester
Sanwa DM509S Insulation Tester
The Sanwa DM509S is a DC insulation resistance tester to measure electric lines’ and equipment’s insulation resistance. The DM509S is IEC61010-1 and IEC61010-2-030 CAT. III 600V certified and has an IP20 rating that protects it against dust and other particles.
Sanwa DM1009S Insulation Tester
Sanwa DM1009S Insulation Tester
The Sanwa DM1009S a DC insulation resistance tester to measure the insulation resistance of electric lines and equipment. The measured voltage is maintained until the low insulation resistance value at the rated current specified in IEC61557-2. This instrument is CAT. III 600V certified.
Sanwa MG500 Insulation Tester
Sanwa MG500 Insulation Tester
- Hot-line state (30V minimum) detection
- Large volt mark with the buzzer sound
- Automatic data hold function
- Bargraph just like analog meter
- Large display with backlight
- Easy to use & tough body
- Display : numeral display 4000
- Sampling rate : 2 times / sec.
Sanwa MG1000 Insulation Tester
Sanwa MG1000 Insulation Tester
- Hot-line state (30V minimum) detection
- Large volt mark with the buzzer sound
- Automatic data hold function
- Bargraph just like analog meter
- Large display with backlight
- Easy to use & tough body
- Display : numeral display 4000
- Sampling rate : 2 times / sec.
Sanwa HG561H Insulation Tester
Sanwa HG561H Insulation Tester
- Electrical circuit not more than Low voltage 600V,
- Insulation resistance of Electric installation, voltage measurement(DC/AC auto detect),
- Resistance measurement, and Continuity check
- Automatically-held readings after measuring MΩ
- The LED level meter shows the reading
- The instrument makes only necessary voltages enabled between 15V, 25V, 50V, 100V, 125V, 250V, and 500V
- Easy-to-read LCD with the fixed decimal point
- Provides the probe that enables you to measure through a hole of a circuit breaker cover
- The lighting lamp illuminates a place to be measured, and the LCD has a backlight.
Sanwa DCM600DR Clamp Meter
Sanwa DCM600DR Clamp Meter
- AC / DC current measurable max. 600A
- True RMS
- Peak hold
When the peak button is pressed, the measuring range will be fixed to the 600A range. - Relative value measurement
- Data hold, Auto power save
- LCD with back light
Sampling rate : 3 times / sec. for numeral display,